What is server in Cisco Packet Tracer?

Hi thanks for replying!

Nội dung chính Show

How to configure a server on Cisco?
How to connect server to PC in Packet Tracer?
How to create a Web server in Packet Tracer?
How to set up DNS server Cisco Packet Tracer?

I am trying to do the following.

PC1 > Switch 1 > Router > DMZ > Webserver

PC2 > Internet Switch > ISP Router > Router > DMZ > Webserver

PC1: IP: 192.168.0.5, Subnet mask: 255.255.255.192, Default gateway: 192.168.0.1

PC2: IP: 8.8.8.100, Subnet mask: 255.255.255.0, Default gateway: 8.8.8.1

Web server (the destination): IP: 2.3.4.5, Subnet mask: 255.255.255.0, Default Gateway, 2.3.4.1

When on PC1 and 2, I am expecting the web browser to be able to access 2.3.4.5. This is just a dummy web page of "corp.com". When trying to access http://2.3.4.5 it produces the error "Server Reset Connection". If I access the web server and try the webpage it loads.

I have tried the 0.0.0.0 route as you describe but that has not changed the behaviour.

I thought I was able to ping the webserver, but running through the packet simulation, traffic hits "Router" and comes back successful, it does not travel through to the webserver, so I think my routing to the webserver is incorrect.

Do you know what the correct ip route should be? It shows as:

C 2.3.4.0 is directly connected, FastEthernet0/0 (which is the interface out towards webserver)

Hi Cisco Community,

I want to connect from a PC to the internet from Cisco Packet Tracer.

So far I have on my configuration a router, a switch, a web server, a dns server, a cloud and a few computers.

I configured the router with the following command :

enable

configure terminal

Router(config)#hostname Routeur-network

Routeur-network(config)#

Routeur-network(config)#interface vlan 1

Routeur-network(config-if)#ip address 192.168.56.1 255.255.255.192

Routeur-network(config)#ip default-gateway 8.8.8.8

Routeur-network(config)#ip domain-name : domain name

Routeur-network(config)#end

When I use the web browser, I can connect to my router but when I try to connect to google I get the following message :

"Host Name Unresolved"

The computers are properly configured.

The Web server is properly configured and so is the DNS Server.

You can check the attachements.

My questions are :

- Is my router configuration correct ?

- Is there any particular command to enter to get to the internet ?

- Are there any additional configurations to add to the Web Server and the DNS Server

- Do I need a Web Server and a DNS Server to get connected to the internet or can I connect directly through the router ?

I am browsing the net to find a video on this subject, but I cannot find one that is really relevant.

Waiting for your answer.

Best,

Manu

Learn how to configure a web server in Cisco packet tracer and access the internet in packet tracer.

To simulate the internet, we have to configure the server endpoint given. The server has the capabilities to provide the web service.

Download

We have two hosts that will be able to access the internet via an ISP router. Our internal network is connected to the ISP router. The interface of the internal router which is connected to the ISP router has been given public IP address. This is static IP that has been configured on the interface.

ISP router is further connected to the Google web server so after the successful configuration of our network, we should be able to access the google.com

How to configure the web server

We have to open services and click on HTTP service. This service is enabled by default and we can see that server is hosting some files already. These files are present by default and when we point the web browser to this server, this server will serve the web page to our browser.

We have configured this server as a Google web server and it is serving a Google web page. To change the content of the webpage, we have to edit the index file present in the web server.

For testing purposes, we can copy the source code of any side that you want the web server to show and paste it into the index file. After saving the file, the web server will show sites according to the source code.

Now, we can test the web server by opening the browser on the PC and pointing it to the server.

We have to enter the IP address of the web server in the URL and press enter. If everything is configured properly then we should see the browser loading the webpage successfully.

Before opening the browser, we must make sure that the connectivity of the server is fine.

Download the lab and test the Google web server and if you want the server to host any other site then change the index file present on the server.

This lab is the smaller presentation of the big network like the internet. This is the way how the internet works however there are thousands of routers and servers connected forming a huge network.

You can try adding more servers with different sites and access those sites on the browser of the PC.

How to configure a server on Cisco?

Steps to configure DHCP server through CLI..

Go into the config mode. ... .

Exclude IP addresses from being assigned by DHCP by using the ip dhcp excluded-address FIRST_IP LAST_IP. ... .

Create a new DHCP pool with the ip dhcp pool NAME command..

How to connect server to PC in Packet Tracer?

Step 1: Launch Packet Tracer. a. ... .

Step 2: Build the topology. a. ... .

Step 1: Configure the Wireless Router. a. ... .

Step 2: Configure the Laptop. a. ... .

Step 3: Configure the PC. a. ... .

Step 4: Configure the Internet cloud. a. ... .

Step 5: Configure the Cisco.com server. a. ... .

Step 1: Refresh the IPv4 settings on the PC..

How to create a Web server in Packet Tracer?

Step 1: After Installation Open Packet Tracer. Step 2: Implementation– Click End Devices and Then Select PC The Drag Into them In the Screen. Result: Step 4: Connect each other with a wire for this click-on connection.